A Bright Reminder - RV Enthusiast Magazine

A Bright Reminder

by | Mar 1, 2022 | DIY Renovations, Electrical, Gadgets

Leaving porch lights on all night can irritate next-door neighbors; adding indictor lights to jog your memory is the simple way to make new friends

How many times have you left your RV’s porch light on all night? Those parked next to you know — and probably wish that you would turn the darn thing off! Just walk around the RV park at night and you’ll see porch lights glowing brightly across patios and into their neighbors’ bedroom windows. It’s one of those things that go out of sight (and mind) when the window coverings are drawn and the door is closed. A solution finally dawned on me one morning after my RV’s porch light had been on all night and one of the neighbors complained: Install an indicator light.

Unfortunately, finding a matching switch with a built-in indicator light proved to be a futile process — and changing to another style switch was not in the cards. However, searching online (Amazon) resulted in finding dozens of small red LED lights that could be mounted in a hole just below the porch light switch assembly. I settled on LED 8mm panel-mount lights (https://amzn.to/3sGsSCp) that come in a package of five for just $5.99. These lights are designed to be mounted on a flat surface, whether it be in wood or metal. Each has a backup nut so it could be tightened and not come loose down the road. Two indicators were installed, one for the porch light and the other for the “scare” lights mounted in the corners of the fifth wheel.

off rv light switches
Numerous small, bright indicator lights can be found online at Amazon and other sources. The choice is varied, so finding the one that suits your tastes might take some time. The best ones will have a threaded retaining nut to make sure the light stays put on the road.
The first step was to mark the location where the lights would be installed. Next, the switch assembly was removed, exposing the wiring. The necessary wires were tested using a multimeter: You need to look for 12-volt DC power when the switches are in the ON position. Finding a suitable ground location may be the trickiest part; check nearby objects — a vent switch, frame members or any type of a light that requires a positive and negative wire. In this case, there was a metal frame rib right at the edge of the switch assembly, which I was able to drill into and install a ground lug for connecting to the indicator lights.

Once the wiring was established, the appropriate size holes were drilled in the wall below the switches, the wires routed through the hole from the front and the retaining nut tightened.

There are a number of ways to splice into the 12-volt DC wires using connectors, but we elected to solder the positive wire from each light to the respective terminals on the switches (small wire-tap terminals can be used if you don’t have a soldering iron). After the ground wires were connected to their respective lights, the switches were turned on and off to test the indicator lights. Once confirmed, the switch assembly was re-installed, being careful that the very small wires did not become detached.

Now, when the porch and/or scare lights are on, the indicators remind me to be kind to my neighbors — and turn off the lights when not outside.

hole being drilled for wiring
The switch assembly for the porch and “scare” lights was removed to expose the wiring. RVs with only a porch light will have one switch plate. If the switch is behind a cabinet door, it will be necessary to route the indicator light to a location outside the compartment.
light switch wiring being crimped
Ground wires were butt-connected to the leads attached to the metal rib located close to the switches. An appropriate ground can be found at nearby metal structures or from leads to other switches if wired in that manner from the factory.
light switch wiring soldered in place
Positive wires from the indicator lights are soldered to the switch terminal connectors that are live when the switch is in the ON position.
rv light switch with led indicators
Indicators mounted below the switches will make sure the occupants are aware that the porch and “scare” lights (if so equipped) are illuminated. It’s pretty hard to miss them.
Get Updates
Subscribe today and never miss an issue!
Get all the latest tips and news to keep you moving on that open road!
RV Enthusiast January/March 2024 Issue
Current Issue
January/March 2024
Spring is back in bloom and with it we are proud to present our latest issue of RV Enthusiast! The January/March issue covers furnace failures and how to fix them, the best batteries for boondocking, quick and easy weekend projects, PLUS so much more!

Already a Subscriber? Click here for Access to the Full Issues.

Share This